This webinar is intended for engineers who work on high-speed digital design and test. In particular, we will be focusing at USB interfaces.
After a quick introduction into USB technology we will be discussing the details of USB 2.0 and 3.2 compliance testing. The webinar will enable you to learn common signal integrity...
Published: Dec 17, 2021
This webinar is intended for engineers who design RF components and systems using tools for simulation and hardware test. We will be introducing a new joint solution approach, developed in cooperation with Cadence. The R&S®VSESIM-VSS solution is enhancing the capabilities of the Cadence® Visual System Simulator™...
Published: Dec 17, 2021
The demands for faster wireless access and lower latency are continuously increasing. To meet these demands and to drive new use cases, regulatory bodies around the world open up spectrum in the 6 GHz band for unlicensed use. This new spectrum allows the Wi-Fi 6 standard, IEEE 802.11ax, to unfold its full power. It will...
Published: Aug 25, 2021
True or false: 30 dBm + 30 dBm = 60 dBm? Why does 1% work out to be -40 dB one time but then 0.1 dB or 0.05 dB the next time? These questions sometimes leave even experienced engineers scratching their heads. Decibels are found everywhere, including power levels, voltages, reflection coefficients, noise figures, field...
Published: Mar 22, 2021
The more successful a gate driver is in reducing power-up and power-down times, the bigger the headache for accurate measurements. Both choosing the right probe and optimizing the probing technique are significant factors in improving measurement accuracy.
This whitepaper provides guidelines.
Published: Jun 04, 2020
To investigate the stability of a switched-mode power supply, a Bode plot created with an oscilloscope is ideal for checking the critical phase margin and gain margin values. The factors that determine how satisfactory the results from Bode plot measurements will be, need to taken into consideration as part of the preparation....
Published: Jun 04, 2020
Today, R&D engineers face challenging time-to-market goals. Extending the product development schedule and delaying the product launch can prove to be extremely costly in terms of opportunity cost and lost market share. Nearly 50% of products fail EMC compliance the first time.
Every day spent on debugging, isolating...
Published: Jun 04, 2020
A VCXO is a crystal oscillator where its output frequency changes in direct proportion to the application of an input control voltage. There are many names given or assigned to this output frequency being changed with the control voltage, which can be confusing.
Absolute Pulling Range (APR) has become a very...
Published: Jul 25, 2018
Rail voltages are getting smaller, and tolerances are decreasing. As a result, making accurate power rail measurements has become much more difficult.
Industry dynamics are driving both a decrease in rail voltage values as well as tighter tolerances across a wide range of rails. Making an accurate ripple measurement...
Published: Jun 04, 2020
Test engineers spend as much as 50 percent of their time (or even more in some cases) actively dealing with obsolescence in their test program sets.
Read about different solutions in the marketplace to help you overcome the challenges you face today.
Also explore best practices...
Published: Mar 03, 2021
5G NR (New Radio) has pioneered the use of mmWave frequencies that provide large bandwidths. This frequency range 2 (FR2), ranging from 24.25 GHz to 52.6 GHz, enables reliable, high data rate transmissions required particularly for demanding real-time applications with low latencies.
This webinar will discuss...
Published: Jul 16, 2021
This webinar is intended for engineers who work on high-speed digital design and test. In particular, we will be focusing at USB interfaces.
After a quick introduction into USB technology we will be discussing the details of USB 2.0 and 3.2 compliance testing. The webinar will enable you to learn common signal integrity...
Published: Sep 27, 2021
Most organizations do not consider production test a top priority, but it is a necessity to prevent major quality issues in the products that represent the company brand in the hands of customers.The costs, however, can be significant and are often greatly misunderstood, especially when there’s no...
Published: Apr 01, 2021
This application note is about creating your own battery model for the R&S®NGM200, beyond the standard models provided within the battery simulation option NGM-K106. The main purpose is to gradually discharge a battery or a rechargeable battery using the internal QuickArb function. The discharge of the battery...
Published: Apr 20, 2021
