This webinar is intended for engineers who work on power electronics design and test. We will be discussing the double-pulse test method, an extremely reliable verification method for converter designs, including switching losses, switching characteristics for all operating modes, and switching times and energies.
...
Published: Dec 17, 2021
This paper describes a method for reducing the power consumption of sensor systems by utilizing the standby functions of a microcontroller (MCU). In concrete terms, the frequency of sensor measurements is reduced, and the system is kept in the standby condition for as long as possible. Furthermore, abnormality detection...
Published: Jul 16, 2018
Fiber optic cable no longer stops at the base of the cell tower. As mobile communication network operators deploy advanced 3G and LTE/4G networks, many are pulling fiber right up the tower. Operators have found that fiber-to-the-antenna (FTTA) architectures offer a number of advantages over legacy coaxial systems, including...
Published: Jul 26, 2018
High-voltage power management ICs, such as TI’s LM5000 series of integrated controllers and regulators, can simplify the design of high-voltage power management solutions
This paper presents various application scenarios where high-voltage capability up to 100V is required and explains how high-voltage power...
Published: Jul 23, 2018
Medical displays specialize in reproducing clear images with high brightness and contrast while maintaining color accuracy. In recent years, there has been a push for smaller and thinner displays in the LCD and LED panel market. In addition, increased performance and image quality has increased heat generation. Therefore,...
Published: Jul 18, 2018
The electronics industry is used to riding waves of growth driven by the introduction of new categories of product. This happened with the PC in the 1980s, with networking gear in the 1990s and more recently with the smartphone. Now ‘wearable electronics’ has emerged as the next potential growth market, prompted...
Published: Jul 19, 2018
This paper briefly describes how amorphous cores are made and describes a method of using SPIKE KILLER and AMOBEADS, small saturable inductors, to improve the recovery characteristics of a diode, which is a major source of output noise.
The manufacture of Toshiba amorphous cores is done by ultra-quenching, a process...
Published: Jul 20, 2018
Effective control of noise and vibration, whatever the application, usually requires several techniques, each of which contributes to a quieter environment.
This paper will focus on the methods of structural damping and vibration isolation, which deal with reducing structural vibration.
Download to...
Published: Jul 17, 2018
This white paper provides an overview of the basic building blocks of a phased array system and discusses how the nature of their design leads to a challenging test environment. Real measurement configuration examples are shown to highlight the flexibility required for T/R module testing.
Register now and get your...
Published: Apr 06, 2020
There are generally two different methods used to protect the pressure transmitter and/or the pressure switch from high temperatures. These two proven methods are done through the use of cooling elements and standoff piping. Provided below are guidelines on how to protect the pressure devices from extreme temperatures...
Published: Jul 17, 2018
Power has always been a design consideration. Traditionally, though, a lower priority has been assigned to power than to most other variables (speed/performance, cost, time-to-market, risk, etc.). In today’s marketplace, however, power has become a very important component in the designer’s decision making...
Published: Jul 19, 2018
This webinar is intended for engineers who work on the design and testing of high-speed interfaces. We will start with typical design challenges and methods in order to approach the signal integrity analysis. Eye measurements will be the focus of this webinar.
After a quick introduction to the basics, we will explore...
Published: Mar 22, 2021
Powder packing machines are used to automatically fill pouches with pharmaceutical powder. In recent years, market demand for improved filling accuracy, processing speed, and reduced device size has increased.
When powder is loaded into the hopper, some suspended powder may be inhaled by workers. For this reason,...
Published: Jul 18, 2018
The LGA80D from Artesyn Embedded Technologies is the first DC-DC converter module of its kind on the market. This innovative non-isolated unit offers two independent and configurable 40 amp, 100 watt outputs, which can also be combined to a single configurable 80 amp, 200 watt output. With a footprint of 1 x 0.5 inches...
Published: Jul 19, 2018
