


In the grand scheme of advanced driver assistance systems (ADAS) and autonomous implementation, replacing a driver requires many hardware and software considerations, not only in sensing technology and processing, but also in electromechanical systems to steer and brake the vehicle. The ADAS trend is leading to newer...
Published: Jul 01, 2022



The following white paper uses a typical off-the-shelf isolated DC-DC converter to demonstrate how an active filter will not only provide superior filtering, as compared to the passive approach, but will also provide a simple turnkey solution to meet challenging transient response requirements.
The performance...



MIPI D-PHY is a practical PHY for typical camera and display applications. It is designed to replace traditional parallel bus based on LVCMOS or LVDS. However, many processors and displays/cameras still use an RGB, CMOS, or MIPI Display Pixel Interface (DPI) as interface. A bridge is often required to connect a processor...



Safety, availability, and cost considerations can make performing thorough tests of embedded control devices using the complete system impractical. Hardware-in-the-loop (HIL) simulation is a real-time test technique used to test these devices more efficiently. During HIL test, the physical system that interfaces...
Published: Apr 01, 2021



According to recent research published by hand tracking and mid-air haptics company Ultraleap, there are widespread concerns among consumers about the health risks of public touchscreens.
With this in mind, what does the future of touchscreens look like for product manufacturers?
Watch this one-hour webinar where...
Published: Aug 19, 2021



This whitepaper will introduce the ECP5™ and LatticeECP3™ FPGAs as viable solutions to overcome embedded design co-processing and connectivity challenges, and highlight application examples at the edge in industrial, consumer, automotive and machine learning areas, where these FPGAs solve the above mentioned...



When it comes to Computer-on-Module (COM) solutions for embedded computing applications, selecting the right form factor and processor for the application can be a challenging task for design engineers.
COM solutions provide a cost-effective computer building block: a COM is a development board featuring a computer...
Published: Jul 06, 2021



In this article, ISSI explores how to use ISSI’s FxLEDTM drivers to open up a new dimension in visibility by using specific colors to make the User Interface (UI) look sleek and informative.
For this application example, an air conditioning appliance was designed with sensors that detect a room’s...



Designers are implementing a wide variety of interface bridging solutions that allow them to transfer data across protocols and, in the process, expand system functionality. The challenge is determining how to most efficiently implement these new bridging solutions without violating system power, footprint and cost requirements....



In some cases, mobile Application Processors (AP) may not have enough interfaces to support the number of image sensor inputs required for a particular application. In other cases, the processing latency between image sensors and imaging data may be too large. The Lattice Semiconductor Dual MIPI CSI-2 to Single MIPI CSI-2...



Though they seem like minor components on a smartphone, automotive dashboard or other consumer electronic device, tactile switches have the ability to influence perceptions of quality. True or not, a bad switch equals a bad device in the minds of many consumers.
So selecting the right switch really can be crucial...



Lattice Semiconductor has developed a display interface in the MachXO2 PLD family. Because this interface is now supported in MachXO2 devices, designers have an even lower cost and very low power alternative to implement embedded displays.
This whitepaper provides an overview of this display standard and explain...



The PFE1100-12-054NA is a 1U form factor, 54 mm wide power supply capable of 1100 watts at high line and de-rates in a low line condition.
This is an AC to DC power-factor-corrected (PFC) power supply that converts standard AC mains power into a main output of 12 VDC for powering intermediate bus architectures,...



Most organizations do not consider production test a top priority, but it is a necessity to prevent major quality issues in the products that represent the company brand in the hands of customers.The costs, however, can be significant and are often greatly misunderstood, especially when there’s no...
Published: Apr 01, 2021