Get products to market faster and with confidence
Tempo Automation is committed to helping our customers stay on schedule and avoid the pitfalls that lead to trouble. As such, we have compiled The PCB Design Development Checklist , a collection of 24 design and build data best practices from Tempo’s experience...
Published: Jan 11, 2022
Read this eBook from Tempo Automation to uncover the 3 key trends accelerating electronics development.
In all engineering domains, development is defined by a Design, Build, and Test (DBT) cycle. Each time a project goes through this cycle, ideas are validated, deficiencies are discovered, and solutions determined....
Published: Jan 11, 2022
This webinar is intended for engineers who work on power electronics design and test. We will be discussing the double-pulse test method, an extremely reliable verification method for converter designs, including switching losses, switching characteristics for all operating modes, and switching times and energies.
...
Published: Dec 17, 2021
Little doubt exists about contemporary battery power and its diverse use potential. With the advent of lighter, smaller, higher powered, lower amperage cells, the technological applications have become “understandably” broad. Significantly, the use of portable medical devices which are battery-powered, has...
Published: Jul 25, 2018
Micro ACTION PIN (MAP) connectors from Tyco Electronics have taken through-hole connector technology to a new level— significantly reducing hole diameters compared to previous designs, while retaining the assembly and operational advantages of press-fit connectors.
This paper briefly reviews the salient electrical...
Published: Jul 25, 2018
QMatrix devices are digital charge-transfer (QT) ICs designed to detect touch using a scanned, passive matrix of electrode sets to achieve a large number of touch keys driven by a single chip.
This configuration leads to a high pin count efficiency in the sensing chip and allows for a small number of connections between...
Published: Jul 23, 2018
This paper shows the need for a new impulse response model and proposes a methodology for its inclusion in timedomain simulations.
The paper also solves another difficult problem by presenting a new technique for converting band-limited S-parameters into ‘base-delay’ causal and passive impulse response...
Published: Jul 25, 2018
This white paper presents a reference design of an IoT sensor system optimized for wearable applications. It describes the challenges that may arise during the feasibility study and design phases of a wearable device and gives practical advice for hardware designers.
Download to find out more.
Published: Jul 20, 2018
Multilayer ceramic capacitors (MLCCs) are ubiquitous in today’s electronics designs. They make up an estimated 30% of the component count in many products, with a market value of more than $8 billion. Recently, there have been shortages in MLCCs, with lead times extending to problematic lengths, and these capacity...
Published: Feb 15, 2019
Servomotors are an integral part of today's automation industry, but traditional circular connections prohibit the miniaturization of such motors due to connector size and the need to isolate power from signal lines.
ITT, Electronic Components has developed innovative technology in the CMX connector series...
Published: Jul 24, 2018
Power system designers can now benefit from flexibility and the ability to customize electrical parameters by using configurable and programmable power supplies as well as fast and low-cost modifications of the electrical and mechanical properties of standard power supplies.
This white paper explains how, through...
Published: Jul 19, 2018
This Application Note was written to provide insight into the one time requirement for ‘type’ testing of power supplies by the safety agency or manufacturer. It will assist in the interpretation of requirements for this testing and provide broad guidelines on exactly what is required of the manufacturer in...
Published: Jul 23, 2018
Silicon carbide diodes have been around for some time now but have had little take-up in power supplies due to their relatively high cost. XP Power has recently adopted a silicon carbide (SiC) diode for the first time in the design of its latest family of modular, configurable power supplies known as fleXPower.
Download...
Published: Jul 23, 2018
Component testers make it easier for users, such as developers or students, to analyze the signal characteristics of active and passive components.
Developers can quickly check the function of a component, while students can apply and verify their theoretical knowledge in practice.
Download to learn more! ...
Published: Nov 06, 2020
